Categories
200-150 Dumps

200-150 Real Exam Dumps Questions and answers 91-100

Get Full Version of the Exam
http://www.EnsurePass.com/200-150.html

Question No.91

In an IEEE 802.3 Ethernet frame, what is the significance of the DSAP field?

  1. The DSAP field specifies the TCP or UDP port that is associated with the transport protocol.

  2. The DSAP field is only used on United States Department of Defense networks to indicate the information classification level.

  3. The DSAP field is only used in Ethernet II frames.

  4. The DSAP field indicates the network layer protocol.

Correct Answer: D

Question No.92

What is the maximum of fabric modules that can be installed in a Cisco Nexus 7000 chassis?

A.

5

B.

6

C.

4

D.

7

Correct Answer: A

Question No.93

Which command can change the sequence of a router boot process?

  1. config-register

  2. configuration-register

  3. conf-register

  4. config-registration

Correct Answer: A

Question No.94

When comparing TCP and UDP segments, which two fields are found only in TCP segment? (Choose two.)

  1. Checksum

  2. acknowledgement

  3. length

  4. source

  5. Sequence number

Correct Answer: DE

Question No.95

Which two layers of the OSI model are combined in the Internet protocol suite network access layer? (Choose two.)

  1. 1

  2. 2

  3. 3

  4. 4

  5. 5

  6. 6

  7. 7

Correct Answer: AB

Explanation:

http://en.wikipedia.org/wiki/Internet_protocol_suite

Question No.96

A switch is configured to be part of a VTP domain so that its VLAN database is not affected by any changes in the domain. Which mode should be configured on this switch?

  1. client

  2. transparent

  3. server

  4. neutral

Correct Answer: B

Question No.97

Which command displays the Trunking Native Mode VLAN on port Ethernet 1/18?

  1. show running-config switchport e1/18

  2. show running-config e1/18 switchport

  3. show interface e1/18

  4. show interface e1/18 switchport

  5. show interface e1/18 native

Correct Answer: D

Explanation:

NX# show interface e1/18 switchport Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Trunking VLANs Allowed: 1-4094

Voice VLAN: none

Question No.98

Refer to the exhibit. Which result command is true?

N7k(config)# interface Ethernet 1/1 N7k(config-if)# storm-control broadcast level 0

  1. All broadcast traffic is suppressed on Ethernet 1/1.

  2. All broadcast and multicast traffic is allowed on Ethernet 1/1.

  3. All broadcast traffic is allowed on Ethernet 1/1.

  4. All broadcast and multicast traffic is suppressed on Ethernet E1/1.

Correct Answer: A

Question No.99

Which statement describes the use of zones in a VSAN?

  1. zones are configured at the fabric core.

  2. An HBA or storage device can belong to one zone.

  3. zones limit unicast, multicast, and broadcast traffic.

  4. zones are a group ports within a single VSAN.

Correct Answer: D

Question No.100

To witch component do you connect the Layer 1 port of a fabric interconnect?

  1. Layer 2 port of the opposite fabric interconnect

  2. out-of band management network

  3. Layer 2 port of the same fabric interconnect

  4. Layer 1 port of the opposite fabric interconnect

    Correct Answer: D

    Get Full Version of 200-150 Dumps

Leave a Reply

Your email address will not be published. Required fields are marked *