Get Full Version of the Exam
http://www.EnsurePass.com/210-065.html
Question No.61
In this item, you will need to use all information presented to you to successfully answer the question.
The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue?
A. |
The subnet mask on the codec is incorrect. |
B. |
The ip address of the codec is incorrect. |
C. |
The interface that the codec is in is in the wrong VLAN. |
D. |
The codec did not receive a DHCP address from the DHCP server. |
Correct Answer: A
Explanation:
The subnet mask configured on the codec is 255.255.255.128, when it should be 255.255.255.0.
Question No.62
A video engineer needs to locate the running version of the Cisco VCS. Under which tab in the Cisco VCS web interface is this information contained?
A. |
Applications |
B. |
Status |
C. |
System |
D. |
Configuration |
Correct Answer: B
Question No.63
Refer to the exhibit. Which option performs a factory reset of a Cisco TelePresence System endpoint?
A. |
Configuration gt; System Settings |
B. |
Configuration gt; Security Settings |
C. |
Troubleshooting gt; Hardware setup |
D. |
Monitoring |
E. |
Troubleshooting gt; Configuration Issues |
F. |
Troubleshooting gt; System Restart |
G. |
A Cisco TelePresence System endpoint can be reset only via CLI. |
Correct Answer: E
Question No.64
What is the importance of defining option 150 in the DHCP server for Cisco TelePresence endpoints?
A. |
Option 150 is not important. |
B. |
It is the TFTP server IPv4 address where the video endpoint retrieves its configuration file while booting. |
C. |
It is the IPv4 address of the default gateway for the subnet that the video endpoint is connected to. |
D. |
It is the configured SIP registrar and proxy server. |
E. |
It is the unique NTP server IPv4 address. |
Correct Answer: B
Question No.65
Which two methods can be used to set the default call protocol of a Cisco TelePresence endpoint running TelePresence codec firmware? (Choose two.)
A. |
Use the GUI and set System gt; H.323 gt; Settings gt; Default Call Protocol gt; H.323. |
B. |
Use the CLI command xConfiguration Conference 1 DefaultCall Protocol: H323. |
C. |
Use the CLI command Conference Default Protocol: H323. |
D. |
Use the CLI command Default Protocol: H323. |
E. |
Use the GUI and set Configuration gt; System Configuration gt; Conference gt; DefaultCall gt; H.323. |
Correct Answer: BE
Question No.66
A customer requests a configuration that enables users to easily add a third party to an existing call. The environment contains only three Cisco TelePresence C40 codecs and one Cisco VCS. To achieve the customer#39;s requirements, which feature should be added?
A. |
Cisco MultiWay |
B. |
Cisco TelePresence Conductor |
C. |
Cisco TMS |
D. |
Cisco Multisite |
E. |
Cisco VCS Expressway |
Correct Answer: D
Question No.67
A technician enters the diag system normal command for a Cisco TelePresence System endpoint. Which action must be done in the CLI before entering this command?
A. |
Logging must be enabled. |
B. |
Calling services must be stopped. |
C. |
All forced upgrades must be cleared. |
D. |
The Telephone_Srvr service must be restarted. |
Correct Answer: B
Question No.68
Which all-in-one dual-screen solution can be used for an average meeting room without the need for external monitors?
A. |
MX700 |
B. |
MX300G2 |
C. |
EX90 |
D. |
SX80 |
E. |
TX9000 |
F. |
MX200G2 |
Correct Answer: A
Question No.69
Refer to the exhibit. Which system tab can be used to add video infrastructure devices and endpoints?
A. |
Navigator |
B. |
System Overview |
C. |
Configuration Templates |
D. |
Provisioning |
E. |
Administrative Tools |
Correct Answer: A
Question No.70
An engineer wants to know if there is a way to determine the optical zoom of a Cisco TelePresence SX20 remotely. Which two methods will retrieve this information? (Choose two.)
A. |
From the CLI, run xstatus. |
B. |
From the CLI, run xconfig. |
C. |
From the web GUI, choose Configuration gt; System Status gt; Camera. |
D. |
From the web GUI, choose Configurationgt; Camera gt; Status. |
E. |
From CLI, run xcommand camera. |
Correct Answer: AC
Get Full Version of 210-065 Dumps