A+ 1002 Study Guide

Free- Exam Objective 3.5 – Dumps4shared

A plus 220-1001 – Exam Objective 3.5

A+ Exam Objective 3.5

Click here if you want to go back to the A+ 220-1001 Table of Content

3.5 Given a scenario, install and configure motherboards, CPUs, and add-on cards.

Click here for our A+ Exam Simulator for exams 220-1001 & 220-1002

Welcome to Exam Notes by Dumps4shared! In this article, we
will cover Core 1 objective 3.5 Given a scenario, install
and configure motherboards, CPUs, and add-on cards.

The Motherboard Form Factor

Although it sounds like the motherboard design is pretty
standardized, the truth is that the original design has evolved dramatically
since its inception. Here we will break them down by design, technically
referred to as their Form Factor, and
the standards that govern them. Form factor is a crucial term. When you refer
to an ATX Form Factor, you have also defined the size of the internal case
dimensions, the connection type, the size of the power supply, and the
measurements and connection type of the Motherboard power. Listed below are the
Form Factors the A+ 220-901 exam is concerned with:


This is the standard motherboard size. It is the platform for
workstations and gaming PCs alike. Its form factor specification calls for a
size of 12.0” by 9.6”. The processor you can use is determined by what will fit
in the socket of the motherboard you’ve chosen. Let’s assume you did your
homework and know that the processor type, motherboard, and memory are all
correct and meet your design requirements. If any one of these are wrong, you will
not have a working PC. Refer to A+ 220-901 sub-objective 1.9 for a good starting
point on this.

Micro-ATX (mATX)

In order to reduce the overall size of PCs, smaller form factors
were introduced. One of these was the Micro-ATX (mATX) which shaves a few
inches off of the length (9.6” by 9.6”). It shares the same power supply
connections with the regular ATX along with the same input/output back panel. mATX
cannot replace a full-size ATX motherboard but it can contain onboard audio. It
also contains at least one expansion slot that can be used by a riser card.

Mini-ITX (aka ITX)

Mini-ITX is by far the favorite by those who seek silence over
performance. That is not to say that performance generates noise, but it does
generate heat which in turn requires cooling which can generate noise.
Obviously given its size, Mini-ITX accommodates fewer components compared to
the other form factors.

Motherboard connector types


The 32-bit PCI (Peripheral Component Interconnect) bus is the oldest expansion slot currently covered under the A+ objectives. It is available in 32 or 64-bit versions and is used to connect legacy hardware to the PC as seen in the image below.

PCI 32 or 64-bit versions

PCI was subsequently replaced by PCI Express (PCI-e) which is
practically the only PCI slot you’ll see today.


PCI-X (where X stands for extended) comes with 32 or 64-bit
slots that are designed to be backwards compatible with 32-bit PCI cards. These
cards are designed to run at 3.3 V. The higher voltage portion of the slot is
beyond what the 32-bit 3.3 V card can reach.


Another variation of PCI is sometimes written as PCI-e (where e
is for Express). PCI-e and PCI-X are not compatible with each other. When using
PCI-Express, 16 lanes of communication are available and the physical size of
the card will determine the number of lanes it may utilize. For example, an x16
slot will accommodate an x1 card

In the following image, you can see the PCI-e 16 slots: The
first one is black and the second is blue. The slots can be used together for
increased bandwidth.

16 slots: The first is black and the second is blue.

Mini-PCI / Mini-PCIe

USB is always an option when adding a wireless card. Here we’ll
talk about internal expansion options: the Mini PCI slot and the Mini-PCIe
slot. Here is how they compare.

Mini-PCI to Mini-PCIe Comparison

The Mini-PCI and the Mini-PCIe slot allow manufacturers to
adjust laptop features to user needs without having to design a new laptop. The
slot works the same way as in desktops, only on a much smaller scale. Accessible
through a service panel, the Mini-PCIe slot is USB 2.0 compliant and can be
used to increase storage capacity, add Bluetooth, or add/upgrade wireless
capabilities. For example, a user with a decent laptop and 802.11 b/g/n
wireless only had to buy an 802.11g or 802.11ac card and swap it out if they
wanted a wireless upgrade. This wireless upgrade required care and patience
because while the card was easy to swap out, the internal antennae have tiny F
type connectors that take time and care to connect. Pictured here is a
Mini-PCIe wireless card ready to be installed. Note the black slot and the gold
antenna connectors. The card will be screwed into a secure position.

True computer portability was born in laptops with the
introduction of the mini-PCI card. This card could be a modem or a wireless
interface card. Improvements have followed but real untethered portability
began with this standard.

Riser cards

Space inside the PC has always been at a premium. One clever
solution is to change the orientation of the installed expansion card. Instead of
installing vertically in a single slot, the riser makes it possible to mount
multiple cards horizontally from one vertical installation (see picture). The
cards can vary in height but this does not have any impact on the case height.
This type of arrangement can support up to four cards per slot. There is
renewed interest with these cards due to the popularity of Home Theater PC
units which need the capabilities of a full size PC with half the space.

Riser Card with two horizontal slots

Click here for our A+ Exam Simulator for exams 220-1001 & 220-1002

CPU Sockets

This section addresses CPU sockets, the processors they support,
and the technologies they employ. The first thing you will notice is that there
are many pin configurations and design variations. There are eleven individual socket
types but these can be grouped into two main categories. The PGA (Pin Grid
Array) type consists of a socket on the motherboard which is made up of a
pattern of small receptors designed to only accept a particular chip’s pin
pattern. Then there is the LGA (Land Grid Array) type which reverses the PGA design
by putting the small fragile pins inside the socket where they have greater
protection against bending and breakage. The LGA design also provides a more
solid connection.

NOTE: Intel favors the LGA package while AMD offers a mix of LGA (TR4)
and PGA chips (AM series and FM2). Intel and AMD processors use incompatible

Asus P7P55-M LGA 1156

Although 32-bit processor architecture is present, most of today’s systems have moved to 64-bit architecture. Another thing to consider is that a new machine today will likely have its GPU (Graphics Processing Unit) integrated on the processor chip.

Notice how the LGA socket is configured to make optimal contact
with an LGA processor. This is a bit of a hardware revolution compared to
previous PGA designs which used pins on the processor chip to make the
connection. These pins are not only fragile but get exposed to more incidental
damage than those in the LGA design which uses the socket to help protect the
pins. Be advised this does not mean that the PGA design is gone. LGA is where
the technology is headed but PGA units exist in vast numbers.

Disable execute bit

Both Intel and AMD processors offer a hardware-based security
feature which prevents application code from executing in specified memory
areas. This feature is known by several names: Execute Disable Bit (EDB) and eXecute
Disable (XD) by Intel and Enhanced Virus Protection (EVP) by AMD. This feature
is generically called the NX bit (no-execute). CompTIA refers to this feature
as the disable execute bit. Although it’s a processor feature, the disable execute
bit must also be supported by the UEFI/BIOS and the operating system. When
enabled, the processor can isolate certain memory areas and prevent the
execution of malware, particularly those that produce buffer overflows.


We start with the SATA connector. This connection uses Serial
Advanced Technology Attachment (SATA) for internal drive connections such as
hard disks and optical drives. SATA is the replacement for Parallel ATA (PATA) which
was the preceding primary drive connection method. Because of its flexibility,
the SATA interface can connect externally to the machine using an eSATA port.
In the table, you can see the internal SATA Data and power connectors. Many
SATA devices ship with a MOLEX-to-SATA adapter cable for power. eSATA connects
external devices. You can distinguish the SATA from eSATA by noting the L
shaped SATA connector. The eSATA connector has a straight rectangular interface
and an external rib on each side of the plug. This feature prevents improper

Front panel / USB

This is for the hundreds of thousands of technicians who spent
their days crawling underneath desks to hook up speakers. We now have
front panel connections for a variety of configurable connectors. This includes
USB which allows for incredible ease of connectivity for a wide variety of
devices. It’s safe to say your prayers (and mine) are answered.

Here are some of the options available for the front panel:
> Audio
> Power button
> Power light
> Drive activity lights
> Reset button

Hooking up the system LEDs while also showing some motherboard
connections and labels.



Here we will look at the PC’s BIOS (Basic Input Output System)
and UEFI (Unified Extensible Firmware Interface) configuration from the CompTIA
A+ 220-901 exam perspective. Your knowledge of these technologies, old and new,
holds the key to success on the A+ exam.

Take the System BIOS or UEFI as an example. Now this is cool!
It’s a GUI! Menu driven! And that is just looks. Now we stop and before the
smart half of the class starts yelling, I’ll take care of this. If you are
using UEFI you don’t have a UEFI BIOS. UEFI Is
. Although they appear to perform similar
functions, the similarities are superficial. For example, changing the boot
drive is a common feature and easily configured for either firmware. The same
is not true for configuring HDD’s that are greater than 4 TB.

OK, we have identified the type of firmware involved and their
roles but suppose you stumble on a working motherboard that has the components
you need onboard! Fantastic news! All you have to do is ensure firmware
compatibility. Depending on your equipment and its level of support, this can
be as simple as pressing a button on the motherboard (UEFI) or as tough as
assembling the whole machine and evaluating the results (BIOS). Refer to the
documentation and choose your path.

In a BIOS configured system, you will encounter a tab based
multilevel interface that is navigated using the keyboard only. Most BIOS have
the following main tabs:

Main: Contains Main entries for system date and time. Shows amount
of installed memory.

Example of main tab in BIOS

Devices: Depending on your
configuration, you may or may not have these choices. If you have the following
items, this is where they will be: Serial Port Setup, USB Setup, ATA Drive
Setup, Video Setup, Audio Setup, and Network Setup.

Advanced:  Will contain settings for the primary
CPU setup and manageability. Items such as Multiprocessing, Hyper Threading,
and Virtualization technologies will be controlled here.

Power: This section controls the system behavior
after a power loss. Power saving settings are also stored here along with
automatic cooling settings (if any).

Security Boot: This section
contains the capability to lock down the system as necessary, from power on and
administrative passwords to setting Secure Boot. Also listed here is the
provision to allow or disallow BIOS flashing.

Exit:  You can save your changes and exit or disregard them if
you made a mistake.

Observing the
BIOS configuration, you will notice settings for:

Boot sequence: Selecting
the order in which device boot data is loaded. This could be anything from a
USB stick, a CD-ROM, or a hard disk. For stronger security, disable USB boot.

Enabling and disabling devices: This
controls which devices will be considered as acceptable when seeking boot data.
Again, consider security factors when making these decisions.

Date/time: Current System
Date/Time. A zero-day attack can be triggered by changing the date.

Clock speeds: Timings set for CPU
and memory. Changing these could easily reduce system stability.

Virtualization support: Enable/disable
hardware virtualization support

BIOS security: Enable/disable security
settings including TPM, passwords, lo-jack, and secure boot.

CMOS Battery

CMOS/UEFI settings (the System Configuration Information) are stored
safely in the firmware. All of these essential settings are maintained by a
small watch battery. When this battery is low or dead, signs of failure include
the loss of the PC date and time and the loss of hard disks. Make certain that the
configuration does not get lost or forgotten by keeping it electronically
refreshed. Firmware is reasonably resistant to data loss but to be safe, it is
periodically refreshed electronically using a tried and true 2032 battery. This
battery model remains unchanged since 1985!

CMOS Battery

CPU features

When selecting your processor and motherboard, the key features
you should be concerned with are the processor speed, the number of cores, and
the amount of cache memory available. When calculating your processor speed, remember
that if you have four 2GHz cores, the resultant speed is not additive. What you
have is four cores capable of operating at 2.0 GHz simultaneously. Your
processor with four 2 Ghz cores does not equate to an 8GHz

A good look in the BIOS/UEFI will flesh out the rest of the
information you need to satisfy this objective. On Intel motherboards, is hyper
threading enabled? You want hyper threading to be active because this enables
your processor to work on multiple tasks, smoothing out the operations and allowing
several things to take place at once.

You also want to check your L1, L2, and L3 cache. These
locations act as temporary holding areas for data that are in process but not
complete. L1 is the fastest and usually the most expensive real estate on the
machine. Generally, L1 cache is in multiples of 64k of fast memory on the
processor chip. Following that will be the L2 cache. Sometimes L2 cache is on
the chip but more often than not it’s on the motherboard. L3 cache, if present,
will be on the motherboard. All of these relatively small storage areas save
the PC from having to save and retrieve data from the system buses during
routine operations.

Virtual technology

You will undoubtedly be tested on this topic. Virtualization
enables you to run multiple instances of complete machines on a single hardware
platform. This is a considerable resource savings and quite a boost to
productivity. Remember to check the BIOS/UEFI first. With virtualization
enabled in BIOS, you can install as many virtual machines as you like! However,
everything must be properly licensed. Once installed, you can’t tell the
virtual machine from the original!

Cooling and
Processor Speeds

Processor speed is defined by the core speed of the processor
multiplied by the speed of the Front Side Bus. The processor speed can be
manipulated. Processor speed is sometimes sped up or “Overclocked” by
increasing the multiplier of the Front Side Bus. This practice can be dangerous
since the faster the processor runs, the hotter it gets. For normal use,
processors come supplied with a 12-volt fan and heatsink that is attached to
the processor via thermal paste and clamps. This provides adequate cooling for
general use but will prove inadequate in extreme situations such as
overclocking. If you intend to overclock the machine, it is important to
upgrade the cooling system to a liquid-based system and add fans to the case. Otherwise,
you will shorten the life of the processor.

Passive Heat Sink

No discussion of heat control in today’s PCs would be complete
without mentioning the original cooling solution. The passive (or fanless)
heatsink consists of a small aluminum block with fins that stick up vertically
to catch airflow and dissipate the heat from the chip. A remarkably simple
design, the passive heatsink creates enormous surface area for more effective
heat exchange.

Thermal Paste

The exchange is where the chip conducts its heat through a layer
of thermally conductive paste which is used to avoid uneven thermal transfer.

Attaching a fan to the passive heatsink creates the more
familiar active heatsink.

Active Heat Sink

The most modern approach for moving heat is the liquid based

This design takes the elements described up to this point and
adds cooling liquid. Sealed and leak-proof, a liquid based cooling system flows
liquid over the chip to absorb the heat. The liquid is then cooled through radiators
located in cooler areas of the machine, dramatically decreasing the
temperature. The cooled liquid is then returned to the chip and the process
repeats continuously.

Liquid Based Cooler

Video cards

Most of today’s PCs ship with video integrated in the
motherboard. These solutions are more than sufficient for the average user.
Very advanced users, such as graphic artists and extreme gamers, will
order custom cards or manually upgrade their video components. Users will seek
cards that have very high frame rates, as much fast memory as they can afford,
and the fastest video interface attainable.

PCI Express 2.0 x16 Video

Here’s a card that fits the bill: PCI Express 2.0 x16 connection,
good speed, fast memory, and lots of connectors. Adapters are usually used for
other possible connections. These expansion cards can be used either as
upgrades or as replacements for a failed motherboard component.

Sound cards

For most PCs, sound chips are being embedded on the motherboards.
If it is deficient, sound will be one of the first PC shortcomings users will
want to address. Usually, upgrades will entail a pair (or more) of speakers and
a more powerful sound card to drive the speakers. Sound cards are usually an
internal device that connects to a PCI expansion slot. A typical sound card is
shown in the image below.

Typical PCI-e-x1 sound card

Network cards

There are two types of network cards: wired and wireless.

Wired network cards

First we will look at the wired cards. These cards have either
Fiber optic, Ethernet, or both. When your Ethernet card fails or if there is a
good reason to upgrade, such as for a faster Ethernet switch, it’s time to look
at your network specifications. Determine the best fit for the new or proposed
network and select the card. Don’t buy it yet! Check your machine for free
ports and make sure that they are compatible with your card choice.

Wireless network cards

The same holds true for wireless cards. Check the specs! Most of
the time, you will end up adding an internal card but it is easy to find USB
models of these cards. It’s easy to see that the wireless networking trend took
off quickly and there were innumerable laptops and portables with Ethernet only
connections installed that needed wireless upgrades. The quickest and easiest
solution to this condition was to develop a USB Wireless adapter. There! All

There are also a number of Wireless network cards available in
PCI and PCI-e configurations.

USB cards

USB Cards provide additional or even faster USB connections to
your PC. Available in several configurations (with internal and external ports),
you can take a PC with USB 1.0 installed and add a USB 3.0 card. If the card
has internal connections, you can also upgrade your hard disk. Ultimately, you
will triple the throughput of your connected devices. If you have any need to
upgrade, consider the USB option for ease of use.

eSATA cards

Covered above.

That’s everything for sub-objective 3.5! Good luck on the test!

Click here if you want to go back to the A+ 220-1001 Table of Content

Click here for our A+ Exam Simulator for exams 220-1001 & 220-1002

Pass Your IT Certification Exams With Free Real Exam Dumps and Questions

Full Version 220-1002 Dumps