Categories
010-151 Dumps

010-151 Real Exam Dumps Questions and answers 41-50

Get Full Version of the Exam
http://www.EnsurePass.com/010-151.html

Question No.41

Which tool does a network administrator not need when installing hardware?

  1. cable tester

  2. wrench set

  3. cable wraps

  4. needle-nose pliers

  5. PCMCIA memory

  6. soldering iron with grounded tip

Correct Answer: F

Question No.42

When the Cisco UCS Manager is used to verify the B- or C-Series device, which two types of Overall Status are acceptable and do not indicate a failure? (Choose two.)

  1. Online

  2. OK

  3. Unassociated

  4. Active

Correct Answer: BC

Question No.43

What is the correct path to verify the Overall Status of Chassis 1 | Server 3?

  1. Equipment Tab gt; Chassis gt; Chassis 1 gt; Servers gt; Server 3 Status tab

  2. Equipment Tab gt; Chassis gt; Chassis 1 gt; Servers gt; Server 3 General tab

  3. Equipment Tab gt; Chassis gt; Chassis 1 gt; Servers gt; Server 3 FSM tab

  4. Servers Tab gt; Chassis gt; Server 3 General tab

  5. Status Tab gt; Chassis gt; Chassis 1 gt; Servers gt; Server 3

  6. Admin Tab gt; Chassis gt; Chassis 1 gt; Servers gt; Server 3 General tab

Correct Answer: B

Question No.44

If the Overall Status for a Cisco UCS B-Series Blade Server indicates a failure in the Cisco UCS Manager, such as discovery-failed, which statement is true?

  1. The server shuts down.

  2. The server automatically reboots reboot in 3 minutes.

  3. The endpoints on that server cannot be upgraded.

  4. The server is online, but the administrator cannot assign a service profile to that blade.

Correct Answer: C

Question No.45

Which action should the administrator take before physically removing a blade server for maintenance or replacement?

  1. Force the server to shut down.

  2. Disassociate the service profile.

  3. Decommission the server.

  4. Perform a graceful shutdown of the server.

Correct Answer: C

Question No.46

Which three statements about powering down a Cisco UCS C-Series Rack-Mount Server to perform maintenance or replacement are true? (Choose three.)

  1. Standby power mode: Power is supplied only to the service processor and the cooling fans, and it is safe to power off the server from this mode.

  2. Power status LED. Green indicates that the server is in main power mode and can be safely powered off.

  3. Graceful shutdown: Press and release the power button. The operating system performs a graceful shutdown, and the server goes to standby mode, which is indicated by an amber power status LED.

  4. Disconnect the power cords from the power supplies in your server to completely power off the server.

  5. Only an emergency shutdown can be performed using the power button on the server front panel.

  6. The Cisco UCS C-Series Rack-Mount Server has only one power mode.

Correct Answer: ACD

Question No.47

Which three components are hot swappable in a Cisco UCS Blade Server and Chassis? (Choose three.)

  1. Fabric Extender

  2. Power supply

  3. Heat sink

  4. SAS Hard Drive

  5. 2x8GB Kit DIMMs

  6. Mezzanine card

Correct Answer: ABD

Question No.48

Which five things should the administrator verify after performing maintenance or replacing a blade server? (Choose five.)

  1. blade server status

  2. hard drive status

  3. host OS boot status

  4. CPU status

  5. mezzanine card status

  6. memory DIMM status

  7. fan and power status

Correct Answer: ABDEF

Question No.49

Which two statements about DIMM replacement in Cisco UCS Servers are true? (Choose two.)

  1. In blade servers, DIMMs can be installed in either 1, 2, 4, or 8 DIMMs per channel.

  2. Rack-mount and blade servers have memory fault LEDs that indicate which DIMM requires attention.

  3. In servers that require pairs of DIMMs, the pairs must be identical (manufacturer, size, part #, and so on).

  4. If the memory in a server is not fully populated, you can install DIMMs in any open slot.

Correct Answer: AC

Question No.50

Which three tools are necessary to console into a Cisco UCS C-Series Rack-Mount Server? (Choose three.)

  1. Cisco DB-9-to-RJ-45 console cable

  2. laptop

  3. monitor

  4. keyboard

  5. KVM dongle

  6. USB serial adapter

Correct Answer: CDE

Get Full Version of 010-151 Dumps

Categories
010-151 Dumps

010-151 Real Exam Dumps Questions and answers 11-20

Get Full Version of the Exam
http://www.EnsurePass.com/010-151.html

Question No.11

Which cable is used to access the command-line interface of a Cisco UCS 6120XP Fabric Interconnects?

  1. KVM cable

  2. console cable

  3. Ethernet cable

  4. SFP Ethernet transceiver cable

Correct Answer: B

Question No.12

Where do you find the model number of a Cisco MDS 9200 Series chassis?

  1. on the top front of the chassis next to the serial number

  2. on the bottom front of the chassis next to the Cisco logo

  3. on the top front of the chassis next to the Cisco logo

  4. on the bottom front of the chassis next to the serial number

Correct Answer: C

Question No.13

How do you find the serial number of a Cisco UCS 5108 Blade Server chassis?

  1. Use the Cisco UCS Admin.

  2. Use the Cisco UCS Application.

  3. Use the Cisco UCS Assistant.

  4. Use the Cisco UCS Manager.

Correct Answer: D

Question No.14

What does the system status LED look like when an over temperature or major alarm occurs on the Cisco UCS 6120XP Fabric Interconnect?

  1. Amber

  2. Red

  3. Blinking amber

  4. Blinking red

Correct Answer: C

Question No.15

Refer to the exhibit. Which item does F represent?

image

  1. HDD 1

  2. TFP Module

  3. SuperCap Module

  4. CPU 2

  5. CMOS Battery

Correct Answer: D

Question No.16

Refer to the exhibit. Which statement correctly identifies the front panel LEDs on the Cisco UCS C220 Server?

image

  1. A is power button and power status LED; B is identification button and LED; C is system status LED; D is network link activity LED.

  2. A is network link activity LED; B is system status LED; C is power button and power status LED; D is identification button and LED.

  3. A is system status LED; B is network link activity LED; C is power button and power status LED; D is identification button and LED.

  4. A is network link activity LED; B is system status LED; C is identification button and LED; D is power button and power status LED.

Correct Answer: A

Question No.17

Which processor option is supported in the Cisco UCS C420 M3 Server?

  1. up to two Intel Xeon E5-4600 series multicore processors

  2. up to two Intel Xeon E7-4800 series multicore processors

  3. up to four Intel Xeon E5-4600 series multicore processors

  4. two or four Intel Xeon E7-8800 series multicore processors

Correct Answer: C

Question No.18

Which two major components does a Cisco Nexus 1000V Series Switch have? (Choose two.)

  1. Virtual Fiber Channel Module

  2. Virtual Ethernet Module

  3. Virtual Supervisor Module

  4. Virtual Memory Controller Module

  5. Virtual Network Module

Correct Answer: BC

Question No.19

Which Cisco Nexus 5000 Series model supports 1/10G BASE-T ports?

  1. Cisco Nexus 5548P

  2. Cisco Nexus 5548UP

  3. Cisco Nexus 5596UP

  4. Cisco Nexus 5596T

Correct Answer: D

Question No.20

Which Cisco MDS model supports the most Fibre Channel ports per chassis?

  1. MDS 9513

  2. MDS 9509

  3. MDS 9506

  4. MDS 9250i

Correct Answer: A

Get Full Version of 010-151 Dumps

Categories
010-151 Dumps

010-151 Real Exam Dumps Questions and answers 21-30

Get Full Version of the Exam
http://www.EnsurePass.com/010-151.html

Question No.21

Refer to the exhibit. Which Cisco MDS chassis supports the 48-Port 16-Gbps Fibre Channel Switching Module?

image

  1. MDS 9509

  2. MDS 9513

  3. MDS 9710

  4. MDS 9506

Correct Answer: C

Question No.22

Refer to the exhibit. What is the name of this rack-mount server?

image

  1. Cisco UCS C220 Rack-Mount Server

  2. Cisco UCS C240 Rack-Mount Server

  3. Cisco UCS C420 Rack-Mount Server

  4. Cisco UCS C460 Rack-Mount Server

Correct Answer: C

Question No.23

Which supervisor module is supported by a Cisco Nexus 7700 Series Switch?

  1. first-generation supervisor module

  2. second-generation supervisor module (Sup2)

  3. second-generation supervisor enhanced module (Sup2E)

  4. third-generation supervisor enhanced module (Sup3E)

Correct Answer: C

Question No.24

Which type of optics module is supported by a 12-port 100 GE Cisco Nexus 7700 F3 Series I/O module?

  1. CPAK

  2. QSFP

  3. SFP/SFP

  4. CFP

Correct Answer: A

Question No.25

Which command-line interface mode is best described by this prompt? UCS-switch-A (nxos)#

  1. maintenance mode

  2. EXEC mode

  3. local management mode

  4. global configuration mode

  5. Cisco IOS mode

Correct Answer: B

Question No.26

Refer to the exhibit. Which item does A represent?

image

  1. Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers

  2. Virtual Interface Card for Cisco UCS B420 M3 Blade Servers

  3. mLOM for Cisco UCS B420 M3 Blade Servers

  4. Virtual Emulex Adapter Card for Cisco UCS B420 M3 Blade Servers

  5. SuperCap module for Cisco UCS B420 M3 Blade Servers

Correct Answer: C

Question No.27

Which command can be used to exit to EXEC mode from this current mode? switch(config-if) #

  1. Ctrl-C

  2. Ctrl-L

  3. quit

  4. exit

  5. end

Correct Answer: E

Question No.28

Refer to the exhibit. Which call-out accurately shows the current running version of the Cisco UCS Manager management software?

image

  1. A – UCS Manager running version 1.4(1m)

  2. B – IO Module 1 running version 1.4(1m)

  3. C – Interface Card 1 running version 1.4(1m)

  4. D – Kernel running version 4.2(1)N(1.4m)

Correct Answer: A

Question No.29

Which command saves the active configuration to NVRAM?

  1. copy startup-config running-config

  2. copy active-config backup-config

  3. copy running-config startup-config

  4. copy backup-config active-config

Correct Answer: C

Question No.30

Refer to the exhibit. Where is the best place to see whether the system is ready for a Fabric Interconnect failover?

image

  1. A – Overall Status operable

  2. B – L1 Connection

  3. C – Part Details

  4. D – Access

  5. E – High Availability Details

Correct Answer: E

Get Full Version of 010-151 Dumps

Categories
010-151 Dumps

010-151 Real Exam Dumps Questions and answers 31-40

Get Full Version of the Exam
http://www.EnsurePass.com/010-151.html

Question No.31

Refer to the exhibit. Where is the best place to find the B200 BIOS version used in a specific Cisco UCS Manager version?

image

  1. A – Installed Firmware

  2. B – Packages

  3. C – Images

  4. D – Capability Catalog

  5. E – Management Extension

Correct Answer: B

Question No.32

Refer to the exhibit. Where is the best place to see bootflash free space?

image

  1. A – Available Memory

  2. B – Total Memory

  3. C – Local Storage Information

  4. D – High Availability Details

Correct Answer: C

Question No.33

Which command syntax is correct to reset the admin password when the switch is in the kickstart prompt 鈥渟witch(boot) #鈥?

  1. exec -gt; admin-password lt;passwordgt;

  2. connect local-mgmt -gt; admin-password lt;passwordgt;

  3. configure terminal -gt; admin-password lt;passwordgt;

  4. connect nxos -gt; admin-password lt;passwordgt;

  5. admin-password lt;passwordgt;

Correct Answer: C

Question No.34

Refer to the exhibit. Which option should you select to get the output of the show tech-support detail command for the Cisco UCS B-Series blade?

image

  1. A – ucsm

  2. B – chassis

  3. C – fabric-extender

  4. D – rack-server

Correct Answer: B

Question No.35

To do a password recovery on a Cisco NX-OS Switch, which option shows the correct syntax to display the bootflash contents at the switch(boot)#?

  1. display bootflash:

  2. show bootflash:

  3. dir bootflash:

  4. find bootflash:

Correct Answer: C

Question No.36

Refer to the exhibit. Where is the best place to see the power supply status of the blade server enclosure?

image

  1. A – Chassis 1

  2. B – Chassis 1 – PSUs

  3. C – Chassis1 – Servers

  4. D – Rack-Mounts – Servers

  5. E – Fabric Interconnects A – PSUs

Correct Answer: B

Question No.37

Which Cisco NX-OS command displays kernel uptime?

  1. show module

  2. show version

  3. show license

  4. show boot

  5. show interface

Correct Answer: B

Question No.38

Which two commands display the version of Cisco NX-OS code that the device is currently running on? (Choose two.)

  1. show version

  2. show module

  3. show interface

  4. show boot

  5. show license

Correct Answer: AB

Question No.39

On the Sensors page from the CIMC view, which four tabs are displayed to view further information? (Choose four.)

  1. Power Supply

  2. Fan

  3. Memory

  4. CPU

  5. LEDs

  6. Temperature

Correct Answer: ABEF

Question No.40

Which three options are the minimum browser requirements to log into the Cisco CIMC GUI? (Choose three.)

  1. Java 1.6 or higher

  2. HTTP and HTTPS enabled

  3. Adobe Flash Player 10 or higher

  4. Internet Explorer version 10

  5. Firefox 26.0

  6. Adobe Shockwave Player 11 or higher

Correct Answer: ABC

Get Full Version of 010-151 Dumps

Categories
010-151 Dumps

010-151 Real Exam Dumps Questions and answers 1-10

Get Full Version of the Exam
http://www.EnsurePass.com/010-151.html

Question No.1

Which method is a TCP/IP-based protocol for establishing and managing connections between IPbased storage devices, hosts, and clients?

  1. FCIP

  2. iFCP

  3. iSCSI

  4. FCoE

Correct Answer: C

Question No.2

Which method does FCIP use to enable connectivity of geographically distributed Fibre Channel SANs over IP?

  1. routing

  2. tunneling

  3. handshaking

  4. transporting

Correct Answer: B

Question No.3

Which important feature on the front end is provided to the clients by multiple servers that access the same storage devices across the SAN?

  1. recovery

  2. redundancy

  3. resiliency

  4. security

  5. storage

Correct Answer: B

Question No.4

The Ethernet specification details several different fiber optic media types. What is the wire transmission speed for 100BASE-FX Ethernet?

  1. 10 Mb/s

  2. 100 Mb/s

  3. 1000 Mb/s D. 10000 Mb/s

Correct Answer: B

Question No.5

Which fiber optic cable type is used most often with a Subscriber connector?

  1. dual-mode

  2. single-mode

  3. straight-mode

  4. multi-mode

  5. subscriber-mode

Correct Answer: B

Question No.6

Which type of connection across the network does a SAN allow for multiple servers to access an unlimited amount of storage devices?

  1. any-to-many

  2. many-to-any

  3. any-to-any

  4. any-to-one

  5. one-to-any

  6. one-to-one

Correct Answer: C

Question No.7

Which two statements about the Ethernet media are true? (Choose two.)

  1. A twisted-pair cable system has each pair of wires twisted together to reduce electromagnetic interference.

  2. Compared to multimode fiber, the single-mode fiber is designed for shorter distances with higher cost.

  3. 40 Gigabit Ethernet twinax cables deploy Enhanced Quad Small Form Factor Pluggable (QSFP ) connectors.

  4. The twinax cables can be found in either a shielded twisted-pair or an unshielded twisted-pair variation.

Correct Answer: AC

Question No.8

What is the wire transmission speed for 100GBASE-ER4 Ethernet?

  1. 100 Mb/s

  2. 1 Gb/s

  3. 10 Gb/s

  4. 100 Gb/s

Correct Answer: D

Question No.9

Which two statements about PCIe are true? (Choose two.)

  1. The PCIe link is built around dedicated unidirectional couples of serial, point-to-point connections known as lanes.

  2. You can install a PCI Express x8 adapter into an x4 slot.

  3. The PCIe standard is a bus-based system in which all the devices share the same bidirectional, 32-bit or 64-bit, parallel signal path.

  4. The PCIe 1.0 standard doubles the transfer rate compared to PCIe 2.0.

  5. A link that is composed of four lanes is called an x4 link.

Correct Answer: AE

Question No.10

Which three statements about FCoE are true? (Choose three.)

  1. Allows Fibre Channel and Ethernet networks to share a single, integrated infrastructure.

  2. Encapsulates Fibre Channel frames into Ethernet frames, which allows them to run alongside traditional IP traffic.

  3. Increases capital costs due to the difficulty to manage.

  4. Consolidates I/O traffic in the data center.

Correct Answer: ABD

Get Full Version of 010-151 Dumps